Since I only have a single IDE CD-ROM and single hard disk to show you today (as well as only a single physical IDE connector on my motherboard), I’ve opted to make the hard disk as Master and the CD-Drive as sl
The difficult part is the jumper settings, which will vary according to your device. Basically, you’re looking for something that mentions CS or Cable Select, as well as Master, and Slave. There will be a diagram somewhere. The digrams indicate which pins a jumper should connect. You should be able to remove a jumper with your finger nails, if not then use a pair of very small needle nose pliers and don’t bend the p
Your selected Steam server could be the cause of slow downloads. A massive amount of data is handled by Steams servers, so this shouldn’t be a surprise. But the problem might be having the wrong server selec
Installation is as you would expect. Just insert the screws into the holes drilled in the case and then through the holes in the fan itself. Righty-tighty until the screw is flush with the mount and can’t be tightened further. Because the screws usually have a very flat base you may find that inserting them is difficult. That’s another reason to temporarily tape the fan in place – it will make inserting the screw eas
Once you have a fan of the correct size you need to open your case and line up the fan with the mounting area. It will have four screw holes, as will the fan, so you just need to line up the screw holes on e
2. The cable length will affect your choice too, as IDE cables are usually quite short. If the CD-ROM is far from the hard drives, you will need one cable for the hard drives, and another going to the CD-
In part 1 of this checklist, I will take you through the physical cleaning checkpoints of your desktop computer or laptop. In part 2 I will follow up with a list of things you can do to purge obsolete files, unused programs, crapware and more from your Windows mach
A few months back I showed you how to install a second SATA drive , appropriate if your computer was bought sometime in the last 5 years or so. We also taught you all about partitions and formatting drives, and to completely replace your old drive with a new one – but I skipped over the subject of physically installing IDE hard drives as I considered them to be too old to warrant a tutor
If you own a Nintendo Wii or have access to a Wiimote (they can be picked up relatively inexpensively from eBay or pawnbrokers) then you will be able to take advantage of the device’s wireless connectivity and use it with Wind
Webmail can put unnecessary load on your browser as webmail apps tend to use a lot of AJAX and JavaScript. Fortunately, you can use the bundled Claws Mail email client. Other lightweight alternatives include the Mozilla Thunderbird-like Icedove Mail, which you can install
Whatever electronic equipment you are cleaning, do not clean it while it is turned on! Do turn the device off and remove the power source. Do not use dripping wet sponges or cloths. Do use damp cloths and alcohol-based cleaners as they will dry faster. Do not attempt to dismantle a device if you are unsure whether or not you will be able to put it back together. Do consult a manual or instructions from the manufactu
Cleaning a modern LCD screen isn’t the same as cleaning an old-fashioned CRT monitor. That is because CRTs are covered with glass, while LCD displays have a softer plastic-based surface. To clean your LCD without damaging it, you need a lint-free cloth, distilled water (for dust) or isopropyl alcohol or white vinegar (for oily stains) and a bottle, ideally an atomizer. Spray your cloth with water or a 1:1 isopropyl alcohol : water mixture. Then carefully wipe the screen with the damp cl
You can carefully vacuum the keyboard to remove loose particles and dust. Afterwards, wipe the keys with a lint-free cloth that is lightly dampened. Finally, disinfect the keyboard using alcohol wipes or spray some alcohol-containing cleaner on your cloth. If the keyboard is seriously manky, you can also take it apart and wash the keys in bulk. Be sure to take a photo of the keyboard first, so that it’s easier to re-assem
With the arrival of Spring in the Northern Hemisphere, houses across the globe get a nice cleaning to rid them of dirt and clutter that has accumulated over the past year. Dust and junk also settle on our computer. Whether your PC Component comparisons|Https://pcbuildinsight.com/ is suffering from a clocked up fan or an overloaded hard drive, it is time to give it a thorough spring cleaning. With the following checklist this will be a bre
Also make sure that you have the fan mounted so it blows in the proper direction. The fan should have a printed or molded arrow that shows the direction air flows. Fans can be installed as either an intake (air blowing in) or exhaust (air blowing out). There may also be an arrow that shows the direction of s
All you need to complete installation is power. The fan will come with a three or four-pin female connector like that shown in the picture above. This needs to be plugged into a three or four-pin male adapter located either on the motherboard or power supply. The connector on a motherboard looks like